A thorough analysis of the occurrence, removal and environmental risks of organic micropollutants in a full-scale hybrid membrane bioreactor fed by hospital wastewater.

The Urban Wastewater Treatment Directive recent draft issued last October 2022 pays attention to contaminants of emerging concern including organic micropollutants (OMPs) and requires the removal of some of them at large urban wastewater treatment plants (WWTPs) calling for their upgrading. Many investigations to date have reported the occurrence of a vast group of OMPs in the influent and many technologies have been tested for their removal at a lab- or pilot-scale. Moreover, it is well-known that hospital wastewater (HWW) contains specific OMPs at high concentration and therefore its management and treatment deserves attention. In this study, a 1-year investigation was carried out at a full-scale membrane bioreactor (MBR) treating mainly HWW. To promote the removal of OMPs, powdered activated carbon (PAC) was added to the bioreactor at 0.1 g/L and 0.2 g/L which resulted in the MBR operating as a hybrid MBR. Its performance was tested for 232 target and 90 non-target OMPs, analyzed by UHPLC-QTOF-MS using a direct injection method. A new methodology was defined to select the key compounds in order to evaluate the performance of the treatments. It was based on their frequency, occurrence, persistence to removal, bioaccumulation and toxicity. Finally, an environmental risk assessment of the OMP residues was conducted by means of the risk quotient approach. The results indicate that PAC addition increased the removal of most of the key OMPs (e.g., sulfamethoxazole, diclofenac, lidocaine) and OMP classes (e.g., antibiotics, psychiatric drugs and stimulants) with the highest loads in the WWTP influent. The hybrid MBR also reduced the risk in the receiving water as the PAC dosage increased mainly for spiramycin, lorazepam, oleandomycin. Finally, uncertainties and issues related to the investigation being carried out at full-scale under real conditions are discussed.

Optimisation of Solid-Phase Extraction and LC-MS/MS Analysis of Six Breast Cancer Drugs in Patient Plasma Samples.

In the development of bioanalytical LC-MS methods for the determination of drugs in plasma samples in a clinical setting, adequate sample preparation is of utmost importance. The main goals are to achieve the selective extraction of the analytes of interest and attain thorough matrix removal while retaining acceptable ecological properties, cost-effectiveness, and high throughput. Solid-phase extraction (SPE) offers a versatile range of options, from the selection of an appropriate sorbent to the optimisation of the washing and elution conditions. In this work, the first SPE method for the simultaneous extraction of six anticancer drugs used in novel therapeutic combinations for advanced breast cancer treatment-palbociclib, ribociclib, abemaciclib, anastrozole, letrozole, and fulvestrant-was developed. The following sorbent chemistries were tested: octylsilyl (C8), octadecylsilyl (C18), hydrophilic-lipophilic balance (HLB), mixed-mode cation-exchange (MCX and X-C), and mixed-mode weak cation-exchange (WCX), with different corresponding elution solvents. The samples were analysed using LC-MS/MS, with a phenyl column (150 × 4.6 mm, 2.5 µm). The best extraction recoveries (≥92.3%) of all analytes were obtained with the C8 phase, using methanol as the elution solvent. The optimised method was validated in the clinically relevant ranges, showing adequate precision (inter-day RSD ≤ 14.3%) and accuracy (inter-day bias -12.7-13.5%). Finally, its applicability was successfully proven by the analysis of samples from breast cancer patients.

Study of the Influence of the Wastewater Matrix in the Adsorption of Three Pharmaceuticals by Powdered Activated Carbon.

The use of powdered activated carbon (PAC) as an absorbent has become a promising option to upgrade wastewater treatment plants (WWTPs) that were not designed to remove pharmaceuticals. However, PAC adsorption mechanisms are not yet fully understood, especially with regard to the nature of the wastewater. In this study, we tested the adsorption of three pharmaceuticals, namely diclofenac, sulfamethoxazole and trimethoprim, onto PAC under four different water matrices: ultra-pure water, humic acid solution, effluent and mixed liquor from a real WWTP. The adsorption affinity was defined primarily by the pharmaceutical physicochemical properties (charge and hydrophobicity), with better results obtained for trimethoprim, followed by diclofenac and sulfamethoxazole. In ultra-pure water, the results show that all pharmaceuticals followed pseudo-second order kinetics, and they were limited by a boundary layer effect on the surface of the adsorbent. Depending on the water matrix and compound, the PAC capacity and the adsorption process varied accordingly. The higher adsorption capacity was observed for diclofenac and sulfamethoxazole in humic acid solution (Langmuir isotherm, R2 > 0.98), whereas better results were obtained for trimethoprim in the WWTP effluent. Adsorption in mixed liquor (Freundlich isotherm, R2 > 0.94) was limited, presumably due to its complex nature and the presence of suspended solids.

Influence of Organic Matter on the Sorption of Cefdinir, Memantine and Praziquantel on Different Soil and Sediment Samples.

Pharmaceuticals are known for their great effects and applications in the treatment and suppression of various diseases in human and veterinary medicine. The development and modernization of science and technologies have led to a constant increase in the production and consumption of various classes of pharmaceuticals, so they pose a threat to the environment, which can be subjected to the sorption process on the solid phase. The efficiency of sorption is determined by various parameters, of which the physicochemical properties of the compound and the sorbent are very important. One of these parameters that determine pharmaceutical mobility in soil or sediment is the soil−water partition coefficient normalized to organic carbon (Koc), whose determination was the purpose of this study. The influence of organic matter, suspended in an aqueous solution of pharmaceutical (more precisely: cefdinir, memantine, and praziquantel), was studied for five different types of soil and sediment samples from Croatia. The linear, Freundlich, and Dubinin−Raduskevich sorption isotherms were used to determine specific constants such as the partition coefficient Kd, which directly describes the strength of sorbate and sorbent binding. The linear model proved to be the best with the highest correlation coefficients, R2 > 0.99. For all three pharmaceuticals, a positive correlation between sorption affinity described by Kd and Koc and the amount of organic matter was demonstrated.

Photocatalytic Activity of TiO2 for the Degradation of Anticancer Drugs.

To prevent water pollution, photocatalysis is often used to remove small molecules such as drugs by generating reactive species. This study aimed to determine the photocatalytic activity of two anticancer drugs, imatinib and crizotinib, and to investigate various influences that may alter the kinetic degradation rate and ultimately the efficacy of the process. In order to obtain optimal parameters for the removal of drugs with immobilized TiO2, the mutual influence of the initial concentration of the contaminant at environmentally relevant pH values was investigated using the response surface modeling approach. The faster kinetic rate of photocatalysis was obtained at pH 5 and at the smallest applied concentration of both drugs. The photocatalytic efficiency was mostly decreased by adding various inorganic salts and organic compounds to the drug mixture. Regarding the degradation mechanism of imatinib and crizotinib, hydroxyl radicals and singlet oxygen showed a major role in photochemical reactions. The formation of seven degradation products for imatinib and fifteen for crizotinib during the optimal photocatalytic process was monitored by high-resolution mass spectrometry (HPLC-QqTOF). Since the newly formed products may pose a hazard to the environment, their toxicity was studied using Vibrio fischeri, where the significant luminescence inhibition was assessed for the mixture of crizotinib degradants during the photocatalysis from 90 to 120 min.

Sorption of cefdinir, memantine, praziquantel and trimethoprim in sediment and soil samples.

The everyday use of various pharmaceuticals to treat humans or animals means that they are increasingly found in the environment. Contamination of the soil can cause the active ingredients to be strongly sorbed to the soil or sediment. In the worst case, they can also be expected to occur in the aquatic environment due to their different polarity. In this study, four drugs from different therapeutic classes (trimetoprim, memantine, cefdinir, praziquantel) were used in dissolved form in two sediment and three soil samples to obtain data that can describe their fate and behavior in the environment. The sorption affinities of the pharmaceuticals were described using linear, Freundlich and Dubinin-Radushkevich sorption isotherms. The highest Kd values were obtained for cefdinir, while memantine and praziquantel tended to be present in water due to their very low sorption coefficients. The studied influence of pH showed a negative trend for memantine and trimetoprim, while an increase in ionic strength resulted in higher Kd values for all drugs. The sorption mechanism for all tested samples was best described by the pseudo-secondary kinetic model (R2 > 0.9999).

Activated carbon coupled with advanced biological wastewater treatment: A review of the enhancement in micropollutant removal.

This study consists of a review on the removal efficiencies of a wide spectrum of micropollutants (MPs) in biological treatment (mainly membrane bioreactor) coupled with activated carbon (AC) (AC added in the bioreactor or followed by an AC unit, acting as a post treatment). It focuses on how the presence of AC may promote the removal of MPs and the effects of dissolved organic matter (DOM) in wastewater. Removal data collected of MPs are analysed versus AC dose if powdered AC is added in the bioreactor, and as a function of the empty bed contact time in the case of a granular activated carbon (GAC) column acting as a post treatment. Moreover, the enhancement in macropollutant (organic matter, nitrogen and phosphorus compounds) removal is analysed as well as the AC mitigation effect towards membrane fouling and, finally, how sludge properties may change in the presence of AC. To sum up, it was found that AC improves the removal of most MPs, favouring their sorption on the AC surface, promoted by the presence of different functional groups and then enhancing their degradation processes. DOM is a strong competitor in sorption on the AC surface, but it may promote the transformation of GAC in a biologically activated carbon thus enhancing all the degradation processes. Finally, AC in the bioreactor increases sludge floc strength and improves its settling characteristics and sorption potential.

Nitrofurantoin in sediments and soils: Sorption, isotherms and kinetics.

Nitrofurantoin is nitrofuran antibacterial drug that is most used as a veterinary pharmaceutic compound. This compound, as well as other pharmaceuticals can greatly affect the environment, the soil and organisms in it and pollute aquatic ecosystems. Since it has been used for only a few decades, knowledge of their fate and behaviour in the environment is still limited. Because of that, the aim of this study was to experimentally determine the Kd values of nitrofurantoin in seven different natural soil and seven different sediment samples with different physico-chemical properties. Sorption phenomena were described with Linear, Freundlich and Dubinin-Radushkevich sorption isotherms. Obtained sorption coefficients (Kd) ranged from 3.967 to 5.121 mLg-1 for sediment samples and 3.634-43.06 mL g-1 for soil samples. The influence of ionic strength and pH of the nitrofurantoin solution and kinetics of the sorption and desorption process were also investigated. Results show that an increase in ionic strength and pH reduces the values of sorption coefficient while the mechanism of nitrofurantoin sorption is the best described with the kinetic model of pseudo-second order.

Sorption of albendazole in sediments and soils: Isotherms and kinetics.

Albendazole is a broad-spectrum anthelmintic drug effective against gastrointestinal parasites in humans and animals. Despite the fact that it has been detected in environment (water, sediment and soil), there is no information on its fate in the environment. So, in order to understand the sorption process of albendazole in environment, the sorption mechanism and kinetic properties were investigated through sorption equilibrium and sorption rate experiments. For that purpose, batch sorption of albendazole on five sediment samples and five soil samples from Croatia's region with different physico-chemical properties was investigated. Except physico-chemical properties of used environmental solid samples, the effects of various parameters such as contact time, initial concentration, ionic strength and pH on the albendazole sorption were studied. The Kd parameter from linear sorption model was determined by linear regression analysis, while the Freundlich and Langmuir sorption models were applied to describe the equilibrium isotherms. The estimated Kd values varied from 29.438 to 104.43 mLg-1 at 0.01 M CaCl2 and for natural pH value of albendazole solution (pH 6.6). Experimental data showed that the best agreement was obtained with the linear model (R2 > 0.99), while the rate of albendazole sorption is the best described with the kinetic model of pseudo-second-order. Obtained results point to a medium or even strong sorption of albendazole for soil or sediment particles, which is particularly dependent on the proportion of organic matter, pH, copper and zinc in them.

Isotherm, kinetic, and thermodynamic study of ciprofloxacin sorption on sediments.

In this study, equilibrium isotherms, kinetics and thermodynamics of ciprofloxacin on seven sediments in a batch sorption process were examined. The effects of contact time, initial ciprofloxacin concentration, temperature and ionic strength on the sorption process were studied. The K d parameter from linear sorption model was determined by linear regression analysis, while the Freundlich and Dubinin-Radushkevich (D-R) sorption models were applied to describe the equilibrium isotherms by linear and nonlinear methods. The estimated K d values varied from 171 to 37,347 mL/g. The obtained values of E (free energy estimated from D-R isotherm model) were between 3.51 and 8.64 kJ/mol, which indicated a physical nature of ciprofloxacin sorption on studied sediments. According to obtained n values as measure of intensity of sorption estimate from Freundlich isotherm model (from 0.69 to 1.442), ciprofloxacin sorption on sediments can be categorized from poor to moderately difficult sorption characteristics. Kinetics data were best fitted by the pseudo-second-order model (R 2 > 0.999). Thermodynamic parameters including the Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were calculated to estimate the nature of ciprofloxacin sorption. Results suggested that sorption on sediments was a spontaneous exothermic process.

Novel multiresidue method for determination of pesticides in red wine using gas chromatography-mass spectrometry and solid phase extraction.

A new multiresidue method was developed for determination of 25 pesticide residues in red wine by gas chromatography coupled to mass spectrometry with a single run of 23.63 min. Samples were extracted from wine with solid phase extraction using Oasis HLB. Mixture of methanol and water was used for rinsing, while acetonitrile and n-hexane were used as elution solvents. Method was validated according to SANCO/12571/2013 criteria in wide linearity range (limit of quantification - 400 µg L(-1)). Limits of quantification (LOQ) were well below 10 µg L(-1) for most pesticides and recoveries at 2×LOQ and 10×LOQ concentration levels were in range 70-120%. Precision, expressed as a relative standard deviation, was always under 14%. The method was applied to 32 red wine samples from Croatia. Pesticides were detected in 30 samples with a total of 15 pesticides found, 7 of which were at a high concentration.

Determination of thermodynamic pKa values of pharmaceuticals from five different groups using capillary electrophoresis.

A determination of the thermodynamic acid dissociation constants (pKa) of 22 frequently used pharmaceuticals using capillary electrophoresis in aqueous media is presented in this work. The investigated pharmaceuticals belong to different pharmacological groups: macrolides, fluoroquinolones, sulfonamides, ß-lactams, tetracyclines, and other miscellaneous pharmaceuticals. The electrophoretic mobilities of the investigated analytes were monitored in a pH range from 2.00 to 10.82. The data were fitted with an appropriate mathematical model using a nonlinear regression analysis to obtain pKa values. Experimentally obtained data were well described by the mathematical model chosen for each analyte that was confirmed by r(2) values higher than 0.99 for most of the investigated analytes. Extrapolations to zero ionic strength were used to determine the thermodynamic pKa values. Experimentally obtained acid dissociation constants were interpreted using structural formulae of investigated analytes and the moieties corresponding to specific pKa were identified.

Preparation and application of sulfaguanidine-imprinted polymer on solid-phase extraction of pharmaceuticals from water.

The molecularly imprinted polymers (MIPs) with sulfaguanidine as a template, methacrylic acid, 4-vinylpyridine, and 2-hydroxyethyl methacrylate as functional monomers, ethylene glycol dimethacrylate as a cross-linker and 2,2'-azobis-isobutyronitrile as an initiator have been prepared through the cross-link reaction of polymerization. Solid-phase extraction (SPE) procedure for the extraction of sulfaguanidine from water samples using the prepared MIPs and non-imprinted (NIPs) was evaluated. The best MIP in combination with commercial sorbents was applied for simultaneous extraction of eight pharmaceuticals. New SPE cartridges were prepared by combination of optimal produced MIP and Oasis HLB in 6 mL of polypropilene SPE reservoir. The developed method which includes new SPE cartridge (MIPMAA-Oasis HLB, 400mg/6 mL) and thin-layer chromatography was validated. The method provides a linear response over the concentration range of 0.5-150 µg/L, depending on the pharmaceutical with the correlation coefficients>0.9843 in all cases except for norfloxacin (0.9770) and penicillin G procaine (0.9801). Also, the method has revealed low limits of detection (0.25-20 µg/L), good precision (intra and inter-day), a relative standard deviation below 15% and recoveries above 95% for all eight pharmaceuticals. The developed method by using newly prepared SPE cartridge has been successfully applied to the analysis of production wastewater samples from pharmaceutical industry.

The sorption of sulfamethazine on soil samples: isotherms and error analysis.

In this paper, batch sorption of sulfamethazine on eight soil samples (six from Croatia and two from Bosnia and Hercegovina) with different organic matter contents ranging from 1.52 to 12.8% was investigated. The effects of various parameters such as agitation time, initial concentration, and ionic strength on the sulfamethazine sorption were studied. The experimental data were analysed using a one-parameter model, Linear isotherm, and two two-parameter models, the Freundlich and Dubinin-Radushkevich isotherms. The goodness of fit was measured using the linear regression and the determination coefficient (R(2)) value. Also, the equilibrium data of the two-parameter models were analysed using the residual root mean square error (RMSE), the sum of squares of errors (ERRSQ), and a composite fractional error function (HYBRID). Non-linear regression has better characteristics for analysing experimental data. The obtained sorption coefficients Kd (from 0.25 to 8.10 mL/g) and the Freundlich sorption coefficients KF (from 1.16 to 7.99 (µg/g)(mL/µg)(1/n)) exhibited quite low values, which indicated that sulfamethazine is weakly adsorbed on the evaluated soils, is highly mobile, and has a great potential to penetrate and pollute the ground water. The Dubinin-Radushkevich isotherm was used to estimate the apparent free energy of sorption.

Optimization of matrix solid-phase dispersion for liquid chromatography tandem mass spectrometry analysis of 12 pharmaceuticals in sediments.

The matrix solid-phase dispersion (MSPD) technique accompanied with LC-MS/MS detection for the purpose of determination of 12 pharmaceuticals (sulfaguanidine, sulfadiazine, sulfamethazine, sulfamethoxazole, trimethoprim, roxithromycin, praziquantel, febantel, enrofloxacin, ciprofloxacin, norfloxacin and procaine) applied to sediment samples has been described in this paper. Different parameters, such as the type of solid phase, the elution solvent and its volume have been investigated. The analytes were successfully extracted by C18 as an MSPD sorbent with 5 mL of acetonitrile:5% of oxalic acid=6:4 (v/v) as an elution solvent. The proposed method provides a linear response over the concentration range of 0.0005-100 µg/g, depending on pharmaceuticals with correlation coefficients above 0.9928 in all cases except for trimethoprim (0.9889). Also, the method has revealed low limits of detection (0.125-500 ng/g), good precision (intra and inter-day), a relative standard deviation below 15% and recoveries above 80%, except for roxithromycin, febantel and enrofloxacin. The method has been successfully applied to analysis of different sediment samples.

RO/NF membrane treatment of veterinary pharmaceutical wastewater: comparison of results obtained on a laboratory and a pilot scale.

BACKGROUND: Emerging contaminants (ECs) are commonly derived from industrial wastewater, which is often a consequence of an inadequate treatment of the latter. Improperly pretreated pharmaceutical wastewater could cause difficulties in operations of wastewater treatment plants while incomplete elimination of ECs during the processing might result in their appearance in drinking water. METHODS: This paper deals with membrane treatment of pharmaceutical wastewater on a laboratory and a pilot scale as well as with the removal of the following veterinary pharmaceuticals (VPs) (sulfamethoxazole, trimethoprim, ciprofloxacin, dexamethasone, and febantel). RESULTS: The pretreatment of pharmaceutical wastewater by means of coagulation and microfiltration (MF) prevented the irreversible fouling of the fine porous structure of the reverse osmosis (RO) and nanofiltration (NF) membranes which were used in the final stage of wastewater processing. The percentage of the removal of the selected VPs ranges from 94% to almost 100% in the case of NF and RO membranes in both scales. The recovery percentage concerning the pilot scale amounted to 88%. Membrane cleaning was successfully carried out in both scales. CONCLUSIONS: The differences in retention between laboratory and pilot tests are due to different raw wastewater quality and different recovery and hydrodynamic of the two systems. Fouling and concentration polarization were more pronounced in laboratory setup (frame-plate module) than in pilot unit (spiral module). The proposed integrated membrane treatment (coagulation, MF, NF, and RO) can be employed for treatment of wastewater originating from pharmaceutical factory. The obtained permeate can be safely discharged to sewer system or could be reused in manufacturing process.

Determination of multi-class pharmaceuticals in wastewater by liquid chromatography-tandem mass spectrometry (LC-MS-MS).

An analytical method for multi-class pharmaceuticals determination in wastewater has been developed and validated. Target compounds were: sulfonamides (sulfadiazine, sulfaguanidine, sulfamethazine, sulfamethoxazole), fluoroquinolones (ciprofloxacin, enrofloxacin, norfloxacin), diaminopyrimidine (trimethoprim), anaesthetic (procaine), anthelmintic (praziquantel and febantel), and macrolide (roxithromycin). The method involves pre-concentration and clean-up by solid-phase extraction (SPE) using Strata-X extraction cartridges at pH 4.0. Target analytes were identified and quantitatively determined by liquid chromatography-tandem mass spectrometry using multiple reaction monitoring (MRM). Recoveries were higher than 50% with relative standard deviation (RSD) below 18.3% for three concentrations. Only for sulfaguanidine was low recovery obtained. Matrix effect was evaluated using matrix-matched standards. The method detection limit (MDL) was between 0.5 and 5 ng L(-1) in spiked water samples. The precision of the method, calculated as relative standard deviation, ranged from 0.5 to 2.0% and from 1.4 to 8.3 for intra-day and inter-day analysis, respectively. The described analytical method was used for determination of pharmaceuticals in effluent wastewaters from the pharmaceutical industry.

Development and optimization of the SPE procedure for determination of pharmaceuticals in water samples by HPLC-diode array detection.

This paper focuses on the investigation of different types of SPE sorbents for the preconcentration of eight veterinary pharmaceuticals from water samples. The pharmaceuticals studied were sulfamethazine, sulfadiazine, sulfaguanidine, trimethoprim, oxytetracycline, enrofloxacin, norfloxacin and penicillin G/procaine. Five different SPE materials (Strata-X, Strata-X-C, Strata SDB-L, Strata C8 and Strata C18) from Phenomenex were compared with Oasis HLB with a view to obtaining the best cartridges for all pharmaceuticals investigated. Extraction efficiency was determined by HPLC with diode array detection (DAD). HPLC-DAD separation and quantification of the selected pharmaceuticals were carried out under gradient elution by a binary mixture of 0.01 M oxalic acid and ACN based on cyano modified column (LiChrosphere 100 CN) from Merck. Strata-X provided the best results in the preconcentration of 100 mL water samples, yielding average pharmaceutical recoveries of higher than 90%, except for sulfaguanidine (76.1%). The developed Strata-X-HLPC-DAD method was validated and applied, for the efficient investigation of reverse osmosis/nanofiltration membranes and for the removal of these eight pharmaceuticals from the production wastewater samples. NF90 and XLE membranes were shown to be the best for the rejection of all investigated pharmaceuticals.